Saturn st ec0121 рецепт

Содержание

Рецепты для хлебопечки сатурн st-ec0121
Похожие рецепты
Инструкция по эксплуатации Saturn ST-EC0121
Страница 7
Инструкция и руководство для Saturn ST-EC0121 на русском на английском
BREAD MAKER ХЛЕБОПЕЧКА ХЛІБОПІЧКА.
GB BREAD MAKER Dear Buyer.
Function Introduction AFTER POWER.
degrade the high polish of the surface. Never immerse the h.
minutes,then take itout andclean. .

Рецепты для хлебопечки сатурн st-ec0121

Инструкция по эксплуатации Saturn ST-EC0121

Страница 7

Если во время приготовления пропадет

электричество, автоматическое при-

готовление продолжится через 5-8

минут, даже без нажатия кнопки

“Старт/Стоп”. Если электричества нет

больше 5-8 минут, хлебопечку нужно

включить самостоятельно. Но если

тесто в процессе замешивания, нужно

нажать кнопку “Старт/Стоп” для за-

пуска программы с начала.

УСЛОВИЯ ДЛЯ НОРМАЛЬНОГО

Хлебопечку может работать при раз-

личных температурах, однако при

низкой температуре тесто может под-

няться не так хорошо, что повлияет на

его размер и структуру. Рекомендуемая

температура помещения от +15°С до

Если после запуска программы под

командой меню на дисплее мигает 5

индикаторов вместе со звуковым сиг-

налом, это означает, что температура

внутри слишком высока или отключен

датчик. Программа должна быть оста-

новлена. Откройте крышку и дайте

хлебопечке остыть в течение 10 — 20

При первом включении устройство

может издавать легкий дым и харак-

терный запах. Это нормальное явление

– оно вскоре прекратится. Обеспечьте

для хлебопечки надлежащее венти-

1. Убедитесь в наличии и исправности

2. Очистите все элементы согласно

главе «УХОД И ОЧИСТКА»

3. Включите программу «Выпекание» и

прогревайте без ингредиентов в те-

чение 10 минут. После охлаждения

очистите еще раз.

4. Высушите все элементы и соберите,

аппарат готов к эксплуатации.

1.Вставьте противень и прокрутите по

часовой стрелке до щелчка. Устано-

вите тестомешалку в ведущие валы.

Перед установкой тестомешалки ре-

комендуется заполнить отверстия

маргарином или другим жиром, это

позволит снизить уровень прилипания

теста к лопастям тестомешалки

2.Добавьте ингредиентов в противень.

Придерживайтесь рецепта. Обычно, в

первую очередь, заливается вода или

жидкость, затем добавляется сахар,

соль и мука, в конце добавляются

дрожжи или разрыхлитель.

Примечание: см. рецепт приготовления

при добавлении больших количеств

3. Сделайте пальцем небольшое уг-

лубление в муке с одной стороны и

добавьте туда дрожжи. Следите за тем,

чтобы дрожжи не смешались с жидко-

4. Закройте крышку и подключите

шнур питания к сети

5. Нажмите кнопку МЕНЮ, для выбора

6. Нажмите и удерживайте кнопку

СТАРТ/СТОП для начала работы.

7. Процесс приготовления по про-

грамме Основной хлеб сопровождается

длинным звуковым сигналом. Это го-

ворит о необходимости добавления

ингредиентов. Откройте крышку и

загрузите ингредиенты. Во время вы-

пекания возможен выход пара через

вентиляционные отверстия. Это нор-

8. 10 звуковых сигналов сообщат об

окончании процесса выпекания. На-

жимайте и удерживайте кнопку

СТАРТ/СТОП около 3-5 секунд, чтобы

остановить процесс и вынуть хлеб.

Откройте крышку. Используя при-

хватки, прокрутите противень против

часовой стрелки и аккуратно выньте

его из хлебопечки.

Внимание: помните о том, что

противень и хлеб могут быть очень

горячими, будьте осторожны.

Всегда используйте прихватки.

Источник

Инструкция и руководство для
Saturn ST-EC0121 на русском на английском

26 страниц подробных инструкций и пользовательских руководств по эксплуатации

Рецепт : Хлеб в хлебопечке ( как испечь самый лучший хлеб в хлебопечке ). Мужчина на кухне .

Хлебопечка Saturn. Купить хлебопечку Сатурн. Видео обзор Saturn st ec8770.

Отзыв Хлебопечь Saturn ST-EC0122

Выпечка хлеба в хлебопечке-Тютюнник Дмитрий

Ремонт хлебопечки разборка

BREAD MAKER ХЛЕБОПЕЧКА ХЛІБОПІЧКА.

GB BREAD MAKER Dear Buyer.

We congratulate you on having

bought the device under trade name

We are sure that our devices will

become faithful and reliable assis-

tance in your housekeeping.

Avoid extreme temperature changes.

Rapid temperature change (e.g.

when the unit is moved from freez-

ing temperature to a warm room)

may cause condensation inside the

unit and a malfunction when it is

switched on. In this case leave the

unit at room temperature for at least

1.5 hours before switching it on.

If the unit has been in transit, leave

it indoors for at least 1.5 hours be-

fore starting operation.

Read this booklet thoroughly before

using and save it for future reference

Before using the electrical appliance, the

following basic precautions should always

1. Read all instructions

2. Before using check that the voltage of

wall outlet corresponds to the one shown

on the rating plate.

3. Do not operate any appliance with a

damaged cord or plug or after the ap-

pliance malfunctions, or is dropped or

damaged in any manner. Return appli-

ance to manufacturer or the nearest

authorized service agent for examination,

repair or electrical or mechanical ad-

4. Do not touch hot surfaces. Use handles

5. To protect against electric shock do not

immerse cord, plugs, or housing in water

or other liquid.

6. Unplug from outlet when not in use,

before putting on or taking off parts, and

7. Do not let cord hang over edge of table

8. The use of accessory attachments not

recommended by the appliance manu-

facturer may cause injuries.

9. The appliance can be used by children

aged from 8 years and above and per-

sons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use

of the appliance in a safe way and un-

derstand the hazards involved. Children

shall not play with the appliance.

Cleaning and user maintenance shall not

be made by children unless they are older

than 8 and supervised.

10. Keep the appliance and its cord out of

reach of children less than 8 years.

11. Do not place on or near a hot gas or

electric burner, or in a heated oven.

12. Extreme caution must be used when

moving an appliance containing hot oil or

other hot liquids.

13. Do not touch any moving or spinning

parts of the machine when baking.

14. Never switch on the appliance with-

out properly placed bread pan filled in-

15. Never beat the bread pan on the top

or edge to remove the pan, this may

damage the bread pan.

16. Metal foils or other materials must

not be inserted into the bread maker as

this can give rise to the risk of a fire or

17. Never cover the bread maker with a

towel or any other material, heat and

steam must be able to escape freely. A

fire can be caused if it is covered by, or

comes into contact with combustible

18. Always attach plug to appliance first,

then plug cord into the wall outlet. To

disconnect, turn any control to OFF, then

remove plug from wall outlet.

19. Do not operate the appliance for

other than its intended use.

20. Do not use outdoors.

21. This appliance is intended to be used

in household and similar applications

such as:– staff kitchen areas in shops,

offices and other working environments;

– by clients in hotels, motels and other

residential type environments;

– bed and breakfast type environ-

22. Do not operate the unit without

bread pan placed in the chamber to avoid

damaging the appliance.

23. Save these instructions

Know your bread maker

Function Introduction AFTER POWER.

As soon as the bread maker is plugged

the power supply, a beep will be heard

and the indicating light the Basic program

is on. It is the default setting.

For starting and stopping the selected

To start a program, press the

“START/STOP” button once. A short beep

will be heard and the program starts. Any

other button is inactivated except the

“START/STOP” button after a program

To stop the program, press the

“START/STOP” button for about 3 sec-

onds until a beep confirms that the pro-

gram has been switched off. This feature

will help to prevent any

unintentional disruption to the operation

It is used to set different programs. Each

time it is pressed (accompanied by a

short beep) that the program will vary.

Press the button discontinuously the 5

menus will be cycled to be indicated by

the LED under the indicator cover. Select

your desired program. The functions of 5

menus will be explained below.

1. Basic: kneading, rise and baking

normal bread. You may also add ingre-

dients to add flavor.

2. Whole wheat: kneading, rise and

baking of whole wheat bread. This setting

has longer preheat time to allow the grain

to soak up the water and expand. It is not

advised to use the delay function as this

can produce poor results. The time of this

setting is three hours.

3. Quick: kneading, rise and baking

loaf with baking soda or baking powder.

Bread baked on this setting is usually

smaller with a dense texture.

4. Dough: kneading and rise, but

without baking. Remove the dough and

shaping it to make bread rolls, pizza,

steamed bread, etc.

5. Bake: only baking, no kneading and

rise. Also used to increase the baking

time on selected settings.

Note: The operating time of every set-

Bread can be automatically kept warm

for 60 minutes after baking.

When bread is kept warm, four LED

lights under the Start/stop button are

If you would like to take the bread out,

switch the program off with the

If the power supply has been broken off

during the course of bread making, the

process of bread making will be con-

tinued automatically within 5-8 min-

utes, even without pressing Start/stop

button. If the break time exceeds 5-8

minutes the memory cannot be kept

and the bread maker must be restarted,

but if the dough is no further than the

kneading phase when the power supply

breaks off, you can press the

“START/STOP” straight to continue the

program from the beginning .

The machine may work well in a wide

range of temperatures, but there could

be a difference in loaf size between a

very warm room and a very cold room.

We suggest the room temperature

should be between 15

1. The five LED lights under the “MENU”

button are twinkling, while the buzzer

keep beep, it indicates the temperature

inside is still too high or the sensor is

disconnect. Then the program has to be

stopped. Open the lid and let the ma-

chine cool down for 10 to 20 minutes,

or connect the sensor.

For the first use

The appliance may emit a little smoke

and a characteristic smell when you

turn it on for the first time. This is

normal and will soon stop. Make sure

the appliance has sufficient ventilation.

1. Please check if all parts and acces-

sories are complete and free of dam-

2. Clean all the parts according to the

latter section “Cleaning and Main-

3. Set the bread maker in baking mode

and bake empty for about 10 minutes.

After cooling it down clean once more.

4. Dry all parts thoroughly and as-

sembly them, so the appliance is ready

How to make bread

1. Place the pan in position, then press

down and turn clockwise until they click

in correct position. Fix, the kneading

blade onto the drive shafts. Turn the

kneaders clockwise until they click into

place. It is recommended to fill holes

with heat-resisting margarine prior to

placing the kneaders, this avoids the

dough to stick below the kneaders and

the kneaders could be removed from

2. Place ingredients into the bread pan.

Usually the water or liquid substance

should be put firstly, then add sugar,

salt and flour, always add yeast or

baking powder as the last ingredient.

In case of heavy dough with high rye or

wholemeal portion we advise to re-

verse the order of ingredients. i.e. to fill

in first the dry yeast and flour ,and

finally the liquid to get a better

3. With finger make a small indentation

on one side of the flour. Add yeast to

indentation, make sure it does not

come into contact with the liquid in-

gredients or salt.

4. Close the lid gently and plug the

power cord into a wall outlet.

5. Press the Menu button until your

desired program is selected.

6. Press the START/STOP button to

7. For the program of BASIC, a long

beep sound will be heard during op-

eration. This is to prompt you to add

ingredients. Open the Lid and put in

some ingredients. It is possible that

steam will escape through the vent slits

in the lid during baking. This is normal.

8. Once the process has been com-

pleted 10 beeps sound will be heard.

You can press START/STOP button for

approx. 3-5 seconds to stop the proc-

ess and take out the bread. Open the

Lid and while using oven mitts, firmly

grasp the bread pan handle and gently

pull the pan straight up and out of the

Caution: the Bread pan and bread

may be very hot! Always handle with

9. Let the bread pan cool down before

removing the bread. Then use

non-stick spatula to gently loosen the

sides of the bread from the pan.

10.Turn bread pan upside down onto a

wire cooling rack or clean cooking

surface and gently shake until bread

falls out onto rack.

11. Remove the bread carefully from

the pan and cool for about 20 minutes

12. If you are out of the room or have

not pressed START/STOP button at the

end of operation, the bread will be kept

warm automatically for 1 hour and then

shut power supply down.

13. When do not use or completely

operation, unplug the power cord.

Note: Before slicing the loaf, use

the hook to remove out the

Kneading blade hidden on the

bottom of loaf. The loaf is hot,

never use the hand to remove the

For Quick breads

Quick breads are made with baking

powder and baking soda that activated

by moisture and heat. For perfect quick

breads, it is suggested that all liquids

be placed in the bottom of the bread

pan, dry ingredients on top. During the

initial mixing of quick bread batters and

dry ingredients may collect in the

corners of the pan, it may be necessary

to help machine mix to avoid flour

clumps. If so, use a rubber spatula.

Cleaning and Maintenance

Disconnect the machine from the

power and let it cool down prior to

1. Bread pan: Rub inside and outside

with a damp cloth. Do not use any

sharp or abrasive agents for the con-

sideration of protecting the non-stick

coating. The pan must be dried com-

pletely prior to installing.

2. Kneading blade: If the kneading bar

is difficult to remove from the axle, In

such an event fill the Container with

warm water and allow it to soak for

approx.30minutes.The kneader can

then be easily removed for cleaning.

Also wipe the blade carefully with a

cotton damp cloth; please note both

the bread pan and kneading blade are

dishwashing safe components.

3. Housing: gently wipe the outer

surface of housing with a wet cloth. Do

Abrasive cleaner to clean as this would

degrade the high polish of the surface. Never immerse the h.

degrade the high polish of the surface.

Never immerse the housing into water

4. Before the bread maker is packed

away for storage, ensure that it has

completely cooled down, is clean and

dry, and the lid is closed.

Introduction of bread ingredients

Bread flour has high content of high

gluten (so it can be also called

high-gluten flour which contains high

protein), it has good elastic and can

keep the size of the bread

from sunken after rising. As the gluten

content is higher than the common

flour so it can be used for making bread

with large size and better inner fiber.

Bread flour is the most important in-

gredients of making bread.

Plain flour is made by mixing

well-chosen soft and hard wheat and

applicable for making express bread or

3. Whole wheat flour

Whole wheat flour is made by grinding

whole wheat, it contains wheat skin

Whole wheat flour is heavier and more

nutrient than common flour. The bread

made by whole wheat flour is usually

small in size. So many recipes usually

combine the whole wheat flour and

bread flour to achieve best results.

4. Black wheat flour

Black wheat flour, also named by

“rough flour”, is a kind of high fiber

flour that is similar to whole wheat flour.

To obtain the large size after rising it

must be used in

combination with high proportion of

Cake powder is made by grinding soft

wheat or low protein wheat, which is

specially used for making cakes. Dif-

ferent flour seems to be alike, Actually

or absorbability of various flour differs

largely for growing areas ,growth

reasons, grinding process and storage

life. You may choose flour with different

test, taste and compare in local market,

and select the one which could produce

the best result according to your own

experiences and taste.

6. Corn flour and oatmeal flour

Corn flour and oat flour are made by

grinding corn and oatmeal respectively,

they both are the additive ingredients

of making rough bread, which are used

for enhancing the flavor and texture.

Sugar is very important ingredient to

add sweet taste and color of bread.

While it helps to yeast bread as nour-

ishment. white sugar is largely used.

powder sugar or cotton sugar may be

called by special requirements.

Yeast passes doughy yeasting process,

then produces carbon dioxide, making

bread expand and inner fibre soft.

however, yeast fast breeding needs

carbohydrate in sugar

and flour as nourishment.

1 tsp .active dry yeast =3/4 tsp. instant

1.5 tsp .active dry yeast =1 tsp. instant

2 tsp .active dry yeast =1.5 tsp. instant

Yeast must be stored in refrigerator as

it will be killed at high temperature,

check the date and storage life of your

yeast. Store it back to the refrigerator

as soon as possible after each use.

Usually the failure of bread rising is

caused by the dead yeast.

The ways described below will check

whether your yeast is fresh and active

(1) Pour 1/2 cup warm water (45-50

into a measuring cup

(2) Put 1 tsp. white sugar into the cup

and stir, then sprinkle 2tsp. yeast over

(3) Place the measuring cup in a warm

place for about 10min. Do not stir the

(4) The froth will be up to 1 cup. Oth-

erwise the yeast is dead or inactive.

Salt is necessary to improve bread

flavor and crust color. But salt can also

restrain yeast from rising. Never use

too much salt in a recipe. If you don’t

want to use salt, omit it. And bread

would be larger if without salt.

Eggs can improve bread texture, make

the bread more nourish and larger in

size, add special egg flavor to bread.

When using it must be peeled and

11. Grease, butter and vegetable oil

grease can make bread be soft and

delay storage life. Butter should be

melted or chopped to small particles

prior use, so as to be stir evenly

when you take it out from refrigerator.

12. Baking powder

Baking powder mainly is used to rise

the Ultra Fast bread and cake. As it do

not need rise time and produce gas

which will form bubble or soften the

texture of bread utilizing chemical

The same principle as above. It can

also used in combination with baking

14. Water and other liquid

Water is essential ingredient for mak-

ing bread. Generally speaking, water

temperature between 20

the most proper. But the water tem-

perature should be within 45-500C for

achieving rising speed for make Ultra

Fast bread. The water may be replaced

by fresh milk or water mixed with 2%

milk powder, which may enhance bread

flavor and improve crust color. Some

recipes may call for juice for the pur-

pose of enhancing bread flavor, eg.

apple juice, orange juice, lemon juice

One of important step for making good

bread is utilizing proper amount of in-

It is strongly suggest to use measuring

cup, measuring spoon to obtain accu-

rate amount, otherwise the bread will

be largely influenced.

1. Weighing liquid ingredients

Water, fresh milk or milk powder solu-

tion should be measured with meas-

Observe the level of the measuring cup

with your eyes horizontally.

When you measure cooking oil or other

ingredients, clean the measuring cup

thoroughly without any other ingredi-

2. Measure dry powder

Dry powder should be kept in natural

and loose conditions, level the cup

mouth gently by blade to ensure ac-

3. Ingredient sequence

The sequence of placing ingredients

should be observed, generally speaking,

the sequence is: liquid ingredients,

eggs, salt and milk powder etc. When

ingredients, the flour can’t b e wet by

liquid completely. The yeast can only be

placed on the dry flour. Exclusively,

yeast can’t touch with salt. After the flour

been kneaded for some time and a

beep remind you to put Fruit ingredients

the mixture. If the fruit ingredients are

added too early the flavor will be dimin-

after long time mixing. When you use

the delaying function for a long time,

add the perishable ingredients such as

eggs, fruit ingredient.

Trouble shooting guide

Some
ingredi-
ents ad-
here to
the heat
element
or
nearby,
for the
first use,
oil re-
mained
on the
surface
of heat
element

Unplug the
bread maker
and clean
the heat
element, but
be careful
not to burn
you, during
the first use,
dry operat-
ing and open
the lid.

Keep
bread
warm
and leave
bread in
the bread
pan for a
long time
so that
water is
losing too
much

Take bread
out soon
without
keeping it
warm

It is
very
difficult
to take
bread
out

Kneader
adheres
tightly to
the shaft
in bread
pan

After taking
bread out,
put hot wa-
ter into
bread pan
and im-
merge
kneader for

minutes,then take itout andclean. .

10 minutes,
then take it
out and
clean.

1.Selecte
d pro-
gram
menu is
improper

Select the
proper pro-
gram menu

2.After
operat-
ing, open
cover
several
times
and
bread is
dry, no
brown
crust
color

Don’t open
cover at the
last rise

3.Stir
resis-
tance is
too large
so that
kneader
almost
can’t
rotate
and stir
ade-
quately

Check
kneader hole,
then take
bread pan out
and operate
without load,
if not normal,
contact with
the author-
ized service
facility.

The tem-
perature
in bread
maker is
too high
to make
bread.

Press
“start/stop
” button and
unplug
bread
maker, then
take bread
pan out and
open cover
until the
bread maker
cools down

Bread
pan is
fixed
improp-
erly or
dough is
too large

Check
whether
bread pan is
fixed prop-
erly and
dough is
made ac-

cording to
recipe and
the ingredi-
ents is
weighed
accurately

Bread
size is
so large
as to
push
cover

Yeast is
too much
or flour is
excessive
or water
is too
much or
environ-
ment
tem-
perature
is too
high

Check the
above fac-
tors, reduce
properly the
amount ac-
cording to
the true
reasons

Bread
size is
too
small or
bread
has no
rise

No yeast
or the
amount
of yeast
is not
enough,
more-
over,
yeast
may have
a poor
activity
as water
tem-
perature
is too
high or
yeast is
mixed
together
with salt,
or the
environ-
ment
tem-
perature
is lower.

Check the
amount and
performance
of yeast,
increase the
environment
temperature
properly.

Dough
is so
large to
over-
flow
bread

The
amount of
liquids is
so much
as to
make

Reduce the
amount of
liquids and
improve
dough rigid-
ity

dough soft
and yeast
is also
excessive.
1.Used
flour is
not
strong
powder
and can’t
make
dough
rise

Use bread
flour or
strong
powder.

2.Yeast
rate is
too rapid
or yeast
tem-
perature
is too
high

Yeast is used
under room
temperature

2. Exces-
sive wa-
ter
makes
dough
too wet
and soft.

According to
the ability of
absorbing
water, adjust
water on
recipe

1.too
much
flour or
short of
water

Reduce flour
or increase
water

Bread
weight
is very
large
and
organi-
zation
con-
struct is
too
dense

2.too
many
fruit in-
gredients
or too
much
whole
wheat
flour

Reduce the
amount of
correspond-
ing ingredi-
ents and
increase
yeast

1. Exces-
sive wa-
ter or
yeast or
no salt

Reduce
properly
water or
yeast and
check salt

is strong
gluti-
nosity
ingredi-
ents in
bread
such as
butter
and ba-
nanas
etc.

Do not add
strong glu-
tinosity in-
gredients
into bread.

Bread
surface
is ad-
hered to
dry
powder

2.Stir not
ade-
quately
for short
of water

Check water
and me-
chanical
construct of
bread maker

Crust is
too
thick
and
baking
color is
too dark
when
making
cakes or
food
with
exces-
sive
sugar

Different
recipes
or ingre-
dients
have
great
effect on
making
bread,
baking
color will
become
very dark
because
of much
sugar

If baking
color is too
dark for the
recipe with
excessive
sugar, press
start/stop
to interrupt
the program
ahead
5-10min of
intended
finishing
time. Before
removing
out the
bread you
should keep
the bread or
cake in
bread pan
for about 20
minutes with
cover closed